Fire detection systems serve a simple purpose to spot fires early enough to allow for the safe evacuation of personnel and, if possible, for a quick response to put the fire out. With the right fire detection system, the human and equipment costs due to damage can be significantly reduced. Electronic detection systems usually use alarms to quickly alert people nearby or connected to a monitoring system. . This provides warning of a fire to building occupants and can provide information to emergency responders on the location of the fire, speeding the process to control the fire, and a fire protection system aims to protect a building’s occupants while minimizing the damage associated with fire. Overall, the goal is to provide the widest possible window for a safe evacuation and reduced damage to equipment, which will lessen downtime and potential repair costs.

These are control panels containing electrical components such as circuit breakers, switches, relays, and other devices dedicated to the operation of fire pumps.

The Electrical Motor Driven Main Pump’s function is to START automatically when a hydrant valve or sprinkler is activated and to provide adequate water under pressure to the system.The capacity of the pump will differ, basis the size of the system. The pump is stopped manually.

A fire sprinkler system is an active fire protection method, consisting of a water supply system, providing adequate pressure and flow rate to a water distribution piping system, onto which fire sprinklers are connected. Although historically only used in factories and large commercial buildings, systems for homes and small buildings are now available at a cost-effective price.

Hose Rack Assemblies permit readily available means of controlling and suppressing fire by one person. The semiautomatic swing rack with movable pins features an automatic release mechanism, keeping water out of the hose (when the valve is open) until the last fold is released.

Flexible joint is a coupling that can transmit torque between two shafts that are not aligned. A flexible joint between the shafts corrects any misalignment. A flexible joint allows some movement between the steering shaft and the steering box.

Check valves are generally installed in pipelines to prevent backflow. A check valve is basically a one-way valve, in which the flow can run freely one way, but if the flow turns, the valve will close to protect the piping, other valves, pumps etc.Most common types of Check valves are swing, lift (piston and ball), butterfly, stop and tilting-disk.

NRS means Non-Rising Stem. OS&Y means Outside Stem and Yoke. In an NRS valve, the stem will turn to open and close the gate, but the stem does not move up or down as it turns. With an OS&Y valve, as the stem turns, it moves into or out of the valve, which also moves the gate to open or seal the valve. An OS&Y valve is open when the threaded stem extends from the valve. The valve is closed when the stem is not visible above the control wheel.

To provide for easier maintenance, the Y-Strainer should be located where the drain plug can be removed. Additionally, ensure the drain or blow-off is located at the lowest position when installed. If installed in the vertical position, the wye side of the strainer must be pointing downward.

Pressure relief valves (safety relief valves) are designed to open at a preset pressure and discharge fluid until pressure drops to acceptable levels. The three basic types of pressure-relief valves are conventional spring-loaded, balanced spring-loaded, and the pilot operated.

A High-performance electromagnetic flowmeter accurately measures the flow volume of any conductive liquids, such as water, salt water, sewage, pulps, slurry, acid, any mixtures of liquids and solids which have a specific minimum of 5μS/cm of electrical conductivity. Our Clients has been widely used in municipal, wastewater treatment, irrigation, chemicals, as well as industrial liquid processes.

A device that uses the surface area and weight of a liquid column to measure and indicate pressure is known as a manometer. Most gauges calculate the pressure relative to atmospheric pressure as the zero point. Hence, this form of reading is known as gauge pressure. Pressure gauges are analog as well as digital. Four types of pressure measurements are gauge, sealed, absolute and differential.

Supervisory switches detect the status of a fire sprinkler system and relay that information to a central, proprietary, or remote monitoring center or sound a local alarm. It is a mechanical and electrical device connected to a fire protection valve that signals a warning if the valve partially or fully closes.

The device consists of a polypropylene float connected to a simple valve. When the build-up of air within the float chamber exceeds a certain level the float drops, opening the valve and releasing the air trapped within the chamber. You can use it anywhere where there’s a need for air removal from pipes.

A water flow detector, also known as a flow switch, is an electro-mechanical device designed to send an alarm to a monitored panel and/or fire department when a continuous flow of water occurs through a fire sprinkler system’s piping. This flow signifies an activated sprinkler head or a leak in the system.Flow switches help maintain safe and manageable rates of flow by triggering actions in various machines within a system to provide on/off flow control.

Zone Control Valve is a system designed to separate the area in case of maintenance and to get the indication of fire zone on a combination of Butterfly valve, Flow Switch, Pressure Gauge and Test & Drain Valves. Its main purpose it to regulate water flow in the designated “zones” or areas and in some buildings, by floors / levels, thus named zone control valve.

We are Supplier of Stainless Steel Pipe, MS Seamless Pipe Size range as per ANSI B36.10. Steel pipes are available in the market. They are divided into different grades and schedules.

An addressable fire alarm system is one in which all fire and smoke detection devices in a system are connected and communicate both with each other and a central control monitoring location. This interconnectivity allows the control personnel to identify the location or “address” where the initial detection occurred. The information directs the emergency response team to pinpoint their efforts immediately to the precise location of the developing problem.

Addressable multi-sensor detector(s) are designed to work with Addressable panel. These detectors are low profile, polarity free, and have dual LED’s for 360° visual indications. The LED’s are blinking in normal operating condition whereas the LED’s in steady state indicate fire status. Multi-sensor detectors use a combination of more than one type of sensor – smoke, heat, or carbon monoxide – to detect the presence of a fire.

Primary power to the fire alarm system can be provided by the electric utility, an engine-driven generator. Requires two External Power supplies for independent and reliable sources of power for fire alarm systems: a primary and a secondary source.

Addressable Intelligent multisensory detector. This device is intended to be used for an addressable automatic fire detection system to detect the presence of smoke, smoke density, and abnormal temperature for fire alarms. Three types of heat detectors -Fixed-temperature detectors; Rate of rise detectors; Rate compensated; Combination rate of rise and fixed temperature.

If a fire is discovered before the fire alarm system is activated, the addressable manual call point allows occupants to trigger the system from a single location. As part of an addressable fire alarm system, each installed call point is assigned an “address”. This allows for authorized personnel to quickly identify the exact device that has been activated, and in turn saves time for the emergency services to locate the origin of the fire.

A device which senses smoke by projecting a light beam from a transceiver unit across the protected area to a reflector that returns the light signal back to the transceiver unit. Smoke entering the beam path will decrease the light signal causing an alarm.There are two basic types of beam detector: End to End: Transmitter and receiver are mounted at either end of the protected area. Reflective: Transmitter and receiver are mounted in the same housing, and the beam is directed at a specially designed reflector, mounted at the opposite end of the protected area.

A device which senses smoke by projecting a light beam from a transceiver unit across the protected area to a reflector that returns the light signal back to the transceiver unit. Smoke entering the beam path will decrease the light signal, causing a fire alarm sounder to activate and flash.

In PLC, to take the input and to return the output, there are an I/O module. The input modules are used for providing an interface for input devices like different types of switches (push button switch, selector switch, limited switch), sensors. Input modules monitor devices responsible for alarm inputs and confirm signals or technical states etc. The input lines are monitored for open and short circuits. Addressable modules can be independently configured via a fire control panel for status or alarm messages.

The purpose of a PLC Output module is to operate or control a physical device based on field device conditions connected to an input module and decisions made by the PLC program. PLC are divided into three types based on output namely Relay output, Transistor output, and Triac Output PLC. The relay output type is best suited for both AC and DC output devices.